Learn your dad's tools while nothing's broken
The worst time to meet a drill is the night the shelf comes down. Here's how to learn the basics on a quiet Saturday, with someone patient next to you.

Quick answer: Pick one Saturday morning and ask your dad (or grandfather, uncle, or a handy neighbor) to teach you five tools and three jobs. Wear safety glasses, practice on scrap wood first, and return everything cleaner than you borrowed it.
Picture it. It's 10:45 on a Sunday night in your first apartment or dorm. The curtain rod just pulled out of the wall, plaster dust is on the floor, and the rod is somehow still holding the curtain. You don't own a drill. You've never used one. So you text home and ask if you can borrow Dad's, and you hope he'll come show you which end is which.
That's the version where you're rushed, a little embarrassed, and learning on a wall you can't afford to wreck.
The other version costs you one morning.
Ask him the right way
Don't say "can you show me some stuff?" That's too big, and it makes a busy man nod and forget. Ask for something with a start and a finish: "Saturday morning, can you teach me to hang a shelf the right way? I want to do the whole thing myself."
Most dads hear that and light up. Some have been waiting years for it. If yours isn't around, the same ask works with a grandfather, a brother-in-law, a shop teacher, or the guy two doors down who's always got his garage open. Offer to bring the coffee and the donuts. Bring something when you visit. That's just manners.
And if you can't find any of them, a hardware store employee will walk you through a drill for free if you ask a specific question. Go on a weekday morning when it's quiet.
You can find that Saturday morning by getting your hours back from your phone. Two hours is plenty.
The five tools
You don't need his whole garage. You need these:
- A 16-ounce claw hammer. Heavy enough to work, light enough that your wrist doesn't hate you. Learn to hold it near the end of the handle and let the head do the work. Start nails with light taps, then swing.
- A 25-foot tape measure. Hook the end on the edge, read the number, and mark it with a pencil. Then measure again. Everybody who skips the second measurement ends up with a second trip to the store.
- A cordless drill/driver. The big one. More on it below.
- A screwdriver set. Phillips and flathead, a few sizes each. The most common mistake is using one that's too small for the screw, which chews up the head.
- A level. Two feet is fine. Center the bubble between the lines. Your eye will lie to you. The bubble won't.
An adjustable wrench is a close sixth. It turns a nut or fitting under a sink, and it's the tool most people grab for the wrong job.
Learn the drill first
Spend twenty minutes on a scrap two-by-four before you touch a wall.
Find the clutch, the numbered ring behind the chuck. A low number stops the drill from driving a screw too hard. High numbers or the drill symbol are for drilling holes. Most people never touch this ring, and that's why they strip screws.
Practice three things on the scrap:
- Drill a pilot hole with a bit slightly thinner than the screw. It keeps the wood from splitting.
- Drive a screw in until it sits flush, not sunk.
- Back it out in reverse, and then swap bits. Take the battery off first.
Let your dad watch, and let him keep his hands in his pockets. If he grabs the drill to "just show you," gently take it back. You learn with your own hands.
Three jobs worth doing once
Hang a shelf. Use a stud finder or knock along the wall until the sound turns solid. Screw into a stud when you can. When you can't, use the proper wall anchor for the weight, and read the package. Mark the holes with the level on the shelf, drill, and mount. It takes twenty minutes and will make you stand taller for a week.
Fix a loose cabinet door or door handle. Nine times out of ten the screw has just backed out. If the hole is stripped and the screw spins, stuff in a couple of toothpicks dipped in wood glue, snap them off flush, and drive the screw back in. It's an old trick, and it works.
Find the shutoffs. Not a repair, but the one that saves a house. Locate the shutoff valve under each sink and toilet, the main water shutoff, and the breaker panel. Practice turning the water off and on. Leave anything inside the electrical panel and any wiring to a licensed electrician. Knowing where the switch is and what each breaker runs is plenty.
The rules that keep your fingers
- Safety glasses every time. Drills throw chips, hammers throw nail fragments, and eyes don't grow back.
- Clamp the work down. Never hold a board with one hand and drill with the other. When a bit catches, the board spins.
- Tie your hair back and skip loose sleeves and dangling necklaces around anything that spins.
- Keep both hands behind the bit. If a hand's in front of it, it's in the wrong place.
- Slow down when you're frustrated. Nearly every tool injury happens when someone's rushing.
You'll make a mistake or two. A crooked hole in a scrap board is a cheap lesson. A crooked hole in a rental wall costs a patch kit and an hour, and you'll know how to do that too.
Return it better than you found it
When you borrow a tool, bring it back cleaner. Wipe it down. Charge the battery. Put it back exactly where it lives, because a man who can't find his tape measure in his own garage doesn't forget that. If you dulled a bit, replace it before he notices. If you broke something, tell him first.
That habit is what makes people hand you the good tools twice.
And if a man offers to handle it for you, let him hold the ladder, say thanks, and mean it. Help is welcome. But you should be able to say what he's doing and why, and you should know when you don't need to ask in the first place. That's part of deciding what you're worth.
The next time something comes loose at eleven at night, you'll be the one holding the drill.
Cal Brennan
Fitness
Strength coach. Trains fathers, tradesmen and desk workers, which means programs that survive a bad week.
Read next
