Your shingles are cooking from underneath
A 25-year roof that's curling at year twelve usually has an airflow problem, and the fix is often at the eaves, not the ridge.

Quick answer: Shingles that curl early are often being baked or dampened from below. A healthy attic pulls cool air in low at the eaves and pushes hot air out high at the ridge. Check the intake first, because that's where most attics fail.
Picture a roof that was sold to you with a 25- or 30-year rating. It's twelve years old. The edges on the south slope are lifting like stale bread, and the roofer you called says "that's just age." Maybe. But maybe your attic has been running like a toaster oven since the day it was finished.
Shingles are asphalt, and asphalt reacts to heat. Cook one from above and below for a decade and it dries out, shrinks and curls. Trap moisture under the deck and the roof can curl, too. Poor ventilation doesn't cause every curled shingle. Bad manufacturing, bad installation and plain old age all do their share. But ventilation is the one cause you can fix, and it's the one most people never check.
Two kinds of curl
Look at the edges from the ground, or better, from a ladder at the eave.
Clawing is when the middle of the shingle stays flat and the corners turn up. Cupping is when the edges rise along the whole length so the shingle forms a shallow trough. Both can come from heat and moisture trapped under the deck. Neither one fixes itself.
Compare slopes. Curling that's worse on the sun-baked side is no surprise. Curling on every slope, including the shaded one, points harder toward a ventilation or moisture problem, or toward a bad batch of shingles. Take photos of each slope. You'll want them for a roofer and for a warranty claim.
Speaking of which, read the warranty. Many shingle makers expect the attic to be properly ventilated, and a claim on early failure can die right there if it isn't.
The winter side nobody thinks about
Heat gets all the blame, but ventilation also pulls out moisture. Showers, cooking, laundry and breathing put water vapor into the house, and some of it climbs into the attic. In cold weather it condenses on the cold underside of the roof deck.
Go up in January with a flashlight. Frost on the nail tips poking through the deck is a bad sign. So are dark staining on the sheathing and damp insulation. A bath fan that dumps into the attic, instead of through a duct to the outside, is one of the most common culprits. Fixing that costs a length of duct and an exterior vent cap. It's the cheapest repair in this whole piece.
The math takes five minutes
The common rule, and the one in model building codes, is one square foot of net free vent area for every 150 square feet of attic floor. Codes allow 1 to 300 when the vents are balanced between low and high, or when there's a vapor retarder on the warm side of the ceiling.
Say your attic floor is 1,500 square feet. At 1 to 150, that's 10 square feet, or 1,440 square inches, of net free vent area. Split it in half: roughly 720 square inches of intake at the eaves and 720 of exhaust near the ridge.
"Net free" matters. A vent's louvers and screen block part of the opening, so the number on the package is the one to use, not the size of the hole. Plenty of attics have a lot of exhaust and almost no intake. That's backward, and it's the mistake I see most.
Start at the soffit
Walk around the house and look up under the eaves. You want to see either continuous vented soffit or a row of individual vents. Then check a few spots from the attic itself.
What goes wrong, in order of how often:
- Painted-over or never-cut soffit. The panel looks vented from the street, but the plywood behind it is solid. Somebody skipped the cutout.
- Insulation stuffed into the eaves. Blown or batt insulation slides down and plugs the intake. A flashlight at the low edge of the attic will tell you in seconds.
- No baffles. Rafter baffles are rigid foam or cardboard channels that hold insulation back from the roof deck and keep an air path open from soffit to attic. They're cheap and you can staple them in yourself.
- Mixed exhaust types. A ridge vent plus gable vents plus a powered fan means the vents start stealing air from each other. The air takes the shortest path and the rest of the attic stays stagnant.
Ridge vent, box vents or a fan
For most roofs with a decent ridge, a continuous ridge vent over a clean, open soffit is the best setup. It's quiet, it has no moving parts and it works on the whole length of the roof.
The trade-off is that a short ridge or a complex roof with lots of hips and valleys may not give you enough length. Then you add box vents or turtle vents high on the slope. Pick one exhaust style and stick with it.
I'd skip the powered attic fan in most cases. A fan that pulls air out hard can also pull conditioned air up from the house through every gap around the lights and the attic hatch. You pay to cool the air and then pay again to run the fan that sucks it out. Fix the intake first. If a roofer's first recommendation is a fan, ask why.
What you can do and what you shouldn't
You can do the inspection yourself. You can staple in baffles, pull insulation back from the eaves and reroute a bath fan duct. Follow the same logic as the rest of your upkeep, which the home maintenance calendar lays out well. Spring and fall are the best attic seasons.
Do it safely:
- Go up in the morning, not at 3 p.m. in July. A hot attic is miserable and it can make you dizzy.
- Step only on the joists. A foot through the drywall ceiling is expensive and it's the least of what can happen.
- Wear a respirator rated for fine dust, long sleeves and eye protection. Fiberglass and old insulation don't belong in your lungs.
- Tell someone when you're going up.
Cutting new soffit openings or a ridge slot is a different job. It means working on the roof, and the slot has to be cut to the right width without nicking the framing. A fall from a roof can end badly, so hire it out. Same for any section of badly curled shingles that needs replacing. Get at least two quotes, and use the questions in knowing when to stop and how to get a quote you can trust. Ask each roofer how they'll calculate your intake and exhaust. If they can't answer, call someone else.
Buying a house? Add the attic to your walk-through. What your home inspector won't check covers the blind spots, and a flashlight in the attic hatch is a good first move. Curled shingles on a house with blocked soffits tell you how the previous owner treated the place.
One last thing to look at
Lie on the lawn and look at your roof on a clear morning after a cold night. Frost on some patches and not others, or one slope melting off early, can show where heat is leaking up into the attic. It's free, it takes two minutes, and it'll tell you more than a sales pitch will.
Your roof is a system. Treat the air under it like it matters, and the shingles will earn that 25-year number.
Wes Dunbar
Country & Skills
Grew up on an acreage and never quite left. Covers trucks, trades, land, and how to do the thing yourself.
Watch
Worth an hour of your evening
More from Home.
From channels we rate. Plays on YouTube.
Read next
