Caulk the window before the first freeze, not after the stain
A ten-dollar tube and one Saturday afternoon can stop a leak before winter makes it expensive. Most guys do it in the wrong order.

Quick answer: Scrape out the old caulk, clean and dry the gap, then run one steady bead of exterior-grade caulk where the window frame meets the siding or trim. Do it on a dry day above the temperature printed on the tube, usually around 40°F. Leave the little drain slots at the bottom of the window open.
Skip the scraping and you've wasted the tube.
Find the actual leak first
The glass almost never leaks. Water gets in at the edges, where the frame meets the wall, and then it runs somewhere surprising. A stain on the ceiling corner might come from a gap two feet away. By the time you see damp drywall, the water's been getting in for a while.
Run a hose test. Get a parent or your brother to stand inside with a flashlight. You stand outside and spray the wall under the window first, then the sides, then the top. Always bottom to top, or you'll never know which spot did it. Give each section a couple of minutes. When the person inside yells, you've found it.
No hose because it's already freezing? Wait for a windy day, run your hand slowly around the inside edge of the frame, and feel for cold air. A thin strip of tissue paper held near the gap flutters when it's drafty. Wherever air gets in, water gets in too.
Ask first, though. It's your parents' house, and they may know the window has a history. If it's on the second floor, an adult handles the ladder. Nobody's impressed by a cast.
What to buy
You need less than you think.
- A tube of exterior-grade caulk. Pick siliconized acrylic latex if you'll paint over it, or 100% silicone if you won't. The label says which.
- A basic caulk gun. The cheap one works fine.
- A putty knife or a 5-in-1 painter's tool.
- A utility knife.
- Painter's tape, a few rags, and a bucket of water.
Don't grab the bathroom caulk because it's the one sitting in the garage. Interior tubes aren't built for sun, rain and a forty-degree daily swing. Read the front of the tube for the word "exterior."
If the gap you're filling is wider than about a quarter inch, caulk alone will sag and crack. Stuff foam backer rod into the gap first. It's a cheap foam cord sold in the same aisle, and it gives the caulk something to grab.
The part everybody skips
New caulk over old caulk is the number one mistake. It looks fast, and it fails by spring. The new bead sticks to the old one, and the old one is already letting go of the wall.
So take the old stuff out. Slice along both edges with the utility knife, then dig it out with the putty knife. It comes off in strips if it's dried out. If it's stubborn, work a little at a time and don't gouge the trim.
Then clean the gap. Brush out dirt, spider webs and old flakes. Wipe it with a damp rag, and let it dry completely. Caulk won't stick to wet or dusty surfaces. Give it an hour on a sunny day. Overnight if there's been rain.
Check the weather before you start, because timing matters more than technique. Many caulks say don't apply below 40°F, and some silicones tolerate colder. The tube will tell you. It also tells you how long before it can see rain, which can be anywhere from a few hours to a full day. Pick a morning with a dry forecast. Keep the tube indoors overnight, too. Cold caulk is stiff as peanut butter in a freezer, and it's a miserable thing to squeeze.
Laying the bead
Put painter's tape on the wall and on the frame, leaving a gap about as wide as you want the bead. It's the difference between a clean line and one that looks like a toddler did it.
Cut the tip of the tube at a 45-degree angle, and cut it small. You can always cut more. Poke the inner seal with a long nail. Load the gun.
Now the technique. Hold the gun at an angle and push the bead ahead of the nozzle instead of dragging it behind. Pushing forces caulk into the gap. Pulling just lays it on top. Go at the speed of someone walking around a church parking lot. Steady squeeze, steady movement. Don't stop halfway down a side, because the seam shows. If you have to stop, release the trigger lock and wipe the tip.
Do one whole side at a time. Right away, smooth the bead with a wet fingertip or the back of a plastic spoon. One pass. If you keep fiddling with it, you'll pull it loose and make it worse. Peel the tape while the caulk is still wet, pulling slowly away from the bead.
You'll get it on your hands, your sleeve and possibly the dog. Keep a rag in your back pocket.
Two things you must not seal
The drain slots. Look along the bottom of the outside of the frame on vinyl or aluminum windows. You'll see small slots or holes, called weep holes. They let water that gets into the frame drain back out. Caulk them shut and you've built a tiny swimming pool inside the window. Caulk the seam around the frame. Leave the slots alone.
The window itself. Don't caulk the moving parts. A sash that's painted or caulked shut is a headache, and if it's in your bedroom, it's also your way out in a fire. A bedroom window needs to open from the inside, easily, every time. Seal the edges. Never seal the window closed.
Do the inside too, but second
Once the outside is finished and cured, look at the gap between the interior trim and the wall. A thin line of paintable caulk there kills drafts. It's quick and does a good job at keeping the heat in. But the outside is what stops water, so it gets done first.
Clean up like it wasn't you
Wipe the drips before they dry. Put the cap on the tube, or push a screw into the tip, and tape it so it's usable next year. Wash the putty knife. Sweep up the old caulk strips from the ground under the window so your dad doesn't find them in the mulch in April.
If you borrowed the caulk gun from a neighbor, give it back clean, with the tube of caulk still half full if you used theirs, or with a new tube if you used it up. That's how people end up being the guy someone calls first. The idea runs through reliable men are built at fifteen, not at thirty, and it's a lot easier to prove with a finished window than with a promise.
If you need a bigger project to build the habit on, start with the house you already live in. Every house has one window like this.
Check it in two weeks
Run your finger along the bead after it cures. It should be firm, a little rubbery, and stuck tight at both edges. If you see a gap or a lifted corner, cut that section out and redo it. Small fix. Easier than redoing the ceiling.
The first hard storm is the real test. When it passes, go look at the corner of that ceiling. Dry and quiet is the whole job, and nobody will know you did anything.
Cal Brennan
Fitness
Strength coach. Trains fathers, tradesmen and desk workers, which means programs that survive a bad week.
Read next
