Skip to content
GuideEvergreen guide

Level a mower deck with a tape measure and one free hour

If your lawn has a stair-step on one side or scalped stripes on the other, the fix costs nothing but an hour and a tape measure.

By Wes Dunbar · Country & Skills5 min read
Level a mower deck with a tape measure and one free hour

Quick answer: Disconnect the spark plug, park on flat ground, and set the deck to one height. Measure from the floor to the same blade tip on the left and right. Get them within 1/8 inch. Then set the front a touch lower than the rear, to your manual's number.

You mow the same yard every week. One pass looks fine and the next leaves a ridge, like the grass got a barber on one side and a weed trimmer on the other. You blame the grass. You raise the deck, then lower it, then blame the mower.

Nine times out of ten, the deck isn't level. It's fixable in an hour, and most of that hour is measuring.

Kill it before you touch it

A mower blade is a steel bar turning at highway speed, and it doesn't care that you only meant to check something.

  • Shut the engine off and wait for the blades to stop completely.
  • Pull the spark plug wire and tuck it away from the plug so it can't touch. On a riding mower, take the key out and set the parking brake too.
  • Make sure the blade control (PTO) is off.
  • Wear gloves. Blade edges cut you even when they're dull.

On a walk-behind you may need to tip it. Turn off the fuel valve if there is one, and tip it with the air filter and carburetor facing up. Tip it the other way and oil runs into the filter, and you'll be chasing a smoking mower all summer. Don't lean it against a wall and trust it to stay.

Check the cheap stuff first

A deck can be perfectly adjusted and still cut crooked. Rule out these before you pick up a wrench.

Tires. One tire a few pounds low tilts the whole machine. The correct pressure is printed on the sidewall, and front and rear are often different. Set all of them, left to match right.

The blade. Look at it. A bent blade, usually from a hidden stump or a buried sprinkler head, hangs lower on one end and ruins any measurement you take. If it's bent, replace it. Don't hammer it straight. A dull blade also tears grass and leaves a ragged, brownish cut that looks like an uneven deck, so sharpen it or swap it while you're here.

The underside. Scrape out the packed, wet grass under the deck. A thick crust changes airflow and makes the cut patchy. Cleaning it takes ten minutes and a putty knife.

Park flat and pick a height

Use a garage floor or a driveway, the flattest hard surface you've got. A lawn is not flat, however much it looks it.

Set the deck to a middle height, around three inches. Whatever you pick, use that same height for every measurement and for the whole job.

Measure side to side

Turn the blade until it points left and right across the mower, perpendicular to the direction you drive. On a multi-blade deck, do the same with the outer blades.

Measure from the floor to the cutting edge of the blade tip on the left. Write it down. Measure the right tip. Write that down too.

They should match within 1/8 inch. Most manufacturers allow that much and no more. If you're off by a quarter inch, that's your stripe.

Measure the same part of the blade each time. Use the leading edge of the tip, not the middle of the blade and not a different spot on each side.

Measure front to back

Now turn the blade to point straight forward and back. Measure the front tip and the rear tip.

Most decks want the front a little lower than the back. The usual target is somewhere around 1/8 to 1/4 inch, but the number varies by maker, so check your manual before you trust me. Some call for more, a few for less. A nose-down deck lets the front of the blade do the cutting and the rear clear the clippings out. A deck running nose-high cuts twice and chokes.

If the rear is lower than the front, you've found the other half of your problem. Scalping in the middle of a pass is the classic sign.

Make the adjustment

How you adjust depends on the mower, and this is where manuals earn their keep.

On most riding mowers, the deck hangs from lift links or brackets. Side-to-side adjustment is usually a nut or bolt on a lift arm or rod on one side, which raises or lowers that corner of the deck. Front-to-back adjustment is typically made on the front hanger or the rear lift rods.

Loosen the lock nut, turn the adjuster a half turn at a time, then measure again. Remeasure after every change. One turn can move an edge more than you expect, and it's easy to overshoot and chase it back and forth.

When you've got it, tighten the lock nuts and measure once more. Things shift when you tighten them.

If the numbers won't come into range, look for a bent hanger, a worn bushing, or a cracked deck shell. A deck that sat on a rock or got dropped off a trailer may be bent, and no amount of adjusting will make it true. That's a parts job. Take it to a shop or order the part.

If the tractor's battery has gone flat after sitting all winter, jump it by the same rules in how to jump-start a car without wrecking the electronics. Do that before you reconnect anything else.

Walk-behind mowers

It's simpler. The deck height is set by the wheels, and each wheel has its own adjuster. Set all four to the same notch, then measure from the floor to the blade tip on both sides. If it's off, one wheel's adjuster is stuck or has slipped a notch. Clean and free it up, and don't force it.

Cut a test strip

Reconnect the spark plug wire, start up, and cut a short strip on a section of lawn that isn't dry. Shut it off, look at the strip, and check the edges. A clean flat cut with no ridge means you're done.

Don't expect perfection on bumpy ground. If it's good on the driveway and still ridged in the yard, the lawn itself is uneven and that's a different job.

Last, put it back better than you found it. Wipe the deck, put the wrenches back where they live, and if the tape measure was borrowed from a neighbor, return it with a thank-you.

Check it again once a season, and after any hard hit. It takes five minutes once you've done it the first time.

Wes Dunbar

Country & Skills

Grew up on an acreage and never quite left. Covers trucks, trades, land, and how to do the thing yourself.

Watch

Worth an hour of your evening

More from Skills.

From channels we rate. Plays on YouTube.

    Essential CraftsmanNov 14

    Why Work-Life Balance is a Myth

    This Old HouseNov 15

    How to Choose and Plant a Tree | Ask This Old House

    Essential CraftsmanNov 11

    The Right Work Clothes for Most Jobs

    This Old HouseNov 14

    How to Repaint a Rusty Smoker Grill | Ask This Old House