Skip to content
GuideEvergreen guide

A Used Lathe, a Dead Branch and Your First Bowl

Woodturning looks like a rich man's hobby until you see what a used lathe costs and how much of the wood is free.

By Dean Shaw · Gear & Garage6 min read
A Used Lathe, a Dead Branch and Your First Bowl

Quick answer: Buy a used midi lathe, a face shield and three sharp tools. Spend your first month turning spindles from free wood before you touch a bowl. Plan on roughly $500 to $800 all in, and join a club before you spend a dime of it.

Why it grabs you

You clamp a chunk of ugly firewood between two points, flip a switch, and it spins at a few hundred RPM. You hold a sharp steel gouge against it and a curl of wood comes off like an apple peel. Ten minutes later the log is a smooth cylinder.

That's it. That's the hook.

Most woodworking asks for hours of measuring before anything looks like anything. Turning rewards you almost at once. A handle, a mallet, a candlestick or a pepper mill is an afternoon's work, and you can hold it when you're done. Bowls take a little longer, but the first one that comes out of the shavings and rings when you tap it will ruin you for other hobbies.

It's also a hobby for everybody. Nothing about it needs brute strength. It needs patience, a steady hand and a willingness to sweep a lot of floor.

Buy used, and know what to check

New lathes from the big brands cost real money. Used ones turn up constantly, because people buy one, get busy and park it in the garage. Check Facebook Marketplace, Craigslist, estate sales and the classifieds at your local woodworking club.

You're looking for a midi lathe, the benchtop size that handles a bowl up to about ten or twelve inches. Names you'll see in the used market include Jet, Delta, Rikon, Nova and the budget WEN. Roughly, a tired mini lathe goes for a couple hundred dollars and a solid variable-speed midi for a few hundred more. Prices move, so check what's listed near you before you decide what's fair.

Before you hand over cash, check these:

  • Spin the spindle by hand. It should turn smoothly, with no grinding and no wobble.
  • Look at the spindle threads. Common sizes are 1 inch by 8 threads per inch and 1¼ inch by 8. Know which one it is, because every chuck and faceplate you buy later has to match.
  • Check the Morse taper. Most midis use a #2. The tailstock should hold a center without it falling out.
  • Plug it in and run it. Variable speed is worth paying extra for. You'll want slow for rough stock and fast for finishing.
  • Slide the tailstock and the tool rest. They should lock down hard and stay there.

Surface rust on the bed is fine. Sand it, wax it, move on. A cracked casting or a bent bed is not fine. Walk away.

What it really costs to start

The lathe isn't the only bill. Here's the full list, with the part nobody mentions.

  • Used midi lathe: a few hundred dollars.
  • Full face shield: a basic polycarbonate one runs about the price of dinner out. Wear it every time the lathe is on. Bowl blanks can fly apart, and glasses won't save your face.
  • Three tools: a spindle roughing gouge, a ½ inch bowl gouge and a parting tool. A basic high-speed steel set costs well under a hundred dollars and will carry you for months. A skew chisel is lovely but can wait, because it's the tool that bites beginners.
  • A slow-speed bench grinder and a sharpening jig: this is the secret cost. Turning tools go dull in minutes, and a dull tool catches and throws the work. The Wolverine-style jig system is the standard, and it's what makes sharpening repeatable instead of a guess.
  • Dust protection: a respirator at minimum. Fine wood dust is bad for your lungs, and some woods are worse than others.
  • Calipers, a pencil, sandpaper, a can of finish. Small money.

Add it up and you land around $500 to $800 if you shop patiently. That's my estimate, not a quote. You'll go over it if you buy a fancy chuck on day one.

Don't. A faceplate or a screw chuck holds a bowl blank fine for your first dozen projects. Buy the big four-jaw chuck after you know you'll keep turning.

Your first three things this week

1. Go to a club meeting. Don't buy anything yet. The American Association of Woodturners has local chapters across the country, and most meet monthly. You'll see a turner work a bowl from a log in an hour, and half the room will offer to let you try their lathe. Club members also know who's selling a used lathe, often before it's posted.

2. Buy the safety gear first. Face shield, respirator, and a way to tie back long hair. Wear a snug shirt with short or tight sleeves. No gloves, no dangling cuffs, no necklaces. Anything that can wrap around a spinning piece of wood will.

3. Turn a handle from a branch. Cut a section of hardwood about two inches thick and ten inches long, mount it between centers, and use the roughing gouge to round it. Then cut a small groove with the parting tool. Done. You've learned the basics of tool rest height, bevel contact and light cuts.

Free wood is everywhere. Ask a tree trimmer for the pile in the back of the truck. Maple, cherry and walnut are all good turning wood. Avoid anything with cracks, loose bark or soft rot.

Spindles first, then bowls

Spindle turning means the grain runs along the lathe bed, like a table leg. Bowl turning has the grain running across it, like a pizza on a spinning plate. That cross-grain means the tool is constantly cutting through hard and soft zones, which is why bowls catch beginners out.

Spend your first month on spindles. Make mallets, tool handles, a rolling pin, a set of drawer pulls. Learn to feel the tool ride the bevel and let the wood come to you. Then move to a shallow bowl in green wood, which cuts easier than dry.

If you like working with your hands, the same patience carries over to leatherworking, another craft where sharp tools do the work and rushing ruins it.

Beginner mistakes that cost you

Dull tools. Sharpen before every session and often during one.

Standing in the line of fire. When you start the lathe, stand to the side. Turn the speed down for any piece that's out of balance, and bring it up slowly.

Taking too heavy a cut. Light passes. The tool should hiss, not growl.

Skipping the tool rest check. Spin the work by hand once before you flip the switch. If the rest is close enough to hit it, it'll find a way.

Buying a big lathe before you know the hobby. A midi is enough. Many club members will tell you they wish they'd stayed small longer.

Sanding too soon. Finish the cut cleanly and sanding is quick. Sand to fix a bad cut and you'll be there all night.

Finding your people

The AAW website has a chapter finder. Beyond that, check:

  • Woodcraft and Rockler stores, which post free demos and classes.
  • Community college continuing ed programs.
  • Makerspaces with shared lathes, a good way to try before buying.
  • Local woodworking guilds and craft fairs, where turners hang out beside their tables.

Show up early to your first meeting. Bring a small piece you turned, even a rough one, and ask someone to critique it. Offer to sweep shavings at the end. Turners remember the guy who stayed to clean up, and that's the guy who gets the call when somebody's selling a lathe.

The best part of the hobby is a stranger putting a gouge in your hand and saying, "Try it." Go get that.

Dean Shaw

Gear & Garage

Reads the warranty, the parts list and the long-term owner reviews before anything else. Trucks, tools, watches, and the cheap version that costs more.

Watch

Worth an hour of your evening

More from Hobbies.

From channels we rate. Plays on YouTube.

    Beekeeping Made SimpleNov 18

    How to Start Beekeeping for Absolute Beginners (Step-by-Step Guide)

    David BurnsJan 13

    Beekeeping For Beginners - Simple & Basic

    Doug the Bee GuyApr 30

    Beginning Beekeeping Series Episode 1: Introduction and Equipment

    David BurnsNov 27

    Beekeeping: Why Most Beekeepers Get Stuck at the Beginner Level