Read the split, not the headline wattage on the brick
A 100-watt charger that drops to 30 watts the moment you plug in a second device isn't a 100-watt charger. Here's how to spot the difference in thirty seconds.

Quick answer: Ignore the big number on the box. Find the line that says what each port delivers when more than one is in use. If the brick can't hold your laptop at its full wattage while your phone charges beside it, it's a one-device charger with extra holes in it.
The nightstand test
Picture a hotel desk. One outlet, one brick, three things that need power: a laptop at 40 percent, a phone at 12, and earbuds in a case. You plug everything in and go to dinner.
A good charger has all three full by morning. A bad one gave the laptop its full share for about four seconds, then divided the power up when the other two connected. The laptop crawled and the phone got a trickle. If you were working on that laptop, it may have lost ground even while plugged in.
Nothing was broken. The brick did exactly what its spec sheet allowed. Nobody read the spec sheet.
How a multi-port brick actually works
A charger has one power budget, say 100 watts. That's the total it can pull from the wall and hand out. Each port can't exceed that total, and the ports share it.
Most chargers handle this in one of two ways:
- Fixed split. One USB-C port gets 65 watts, the other gets 35, no matter what. Predictable, easy to understand, and a little wasteful if one port is idle.
- Dynamic split. The brick moves watts around depending on what's plugged in. Alone, the laptop gets 100. Add a phone and it shifts to something like 65 and 30. Smarter, but only as good as its published table.
Neither is a flaw. The flaw is a brand that prints "100W" in huge letters and buries the real numbers in a footnote, or leaves them out completely.
Read the label like this
Flip the brick over, or open the product page and scroll past the photos. You want a table or a line that looks something like this (this is an example, not a specific product):
- One port in use: 100W
- Two ports in use: 65W + 30W
- Three ports in use: 45W + 30W + 18W
Then do the arithmetic against your own gear. Look at the charger that came with your laptop. It says something like 65W on it. Your phone's charger probably says 20W to 45W. Add those up, and that's the number your brick has to deliver across two ports at the same moment.
If the two-port line comes in under that, you'll be throttled. Whether it matters depends on how fast you need things charged. Overnight, it doesn't matter much. Fifteen minutes before you leave for the airport, it matters a lot.
The terms that count
Most of the alphabet soup on the packaging is noise. A few terms aren't.
USB-C Power Delivery (PD). The standard that lets a charger and a device agree on voltage and current before any serious power flows. If your laptop charges over USB-C, it needs PD. A brick without it will either charge slowly or not at all.
PPS. A PD extension that lets the charger adjust voltage in small steps. Some phones, including recent Samsung flagships, use it to reach their top charging speed. On a charger without PPS, those phones still charge, just slower than advertised.
GaN. Gallium nitride, a semiconductor that runs cooler than the older silicon in these bricks. That's why a 100-watt charger can now be the size of a deck of cards. It's a real improvement, but it's not a quality guarantee. A cheap GaN brick is still a cheap brick.
Safety certification. Look for a UL or ETL mark, or a similar listed certification, on the brick itself. Not just a logo on the listing, on the product. This is a device plugged into your wall, often while you sleep. It's the one place to be fussy.
Ports that quietly cap you
USB-A ports are the usual trap. Many multi-port bricks include a couple, and they often top out at a low number such as 12 watts, or they only fast-charge under older, proprietary standards. Plug a phone into one and you may get a fraction of what the same phone gets from a USB-C port.
Fine for earbuds, a watch, a flashlight. Don't use it for anything you're in a hurry to charge.
Also check whether using the USB-A port reduces the USB-C ports. On some bricks, any second port in use drops everything to a lower tier. The table will tell you if you look.
The cable is half the system
A great charger and a bad cable make a slow charger.
Standard USB-C cables are generally rated for up to 60 watts. For anything higher, up to 100 watts, you need a cable built for it, with an identifying chip inside called an e-marker. A lot of laptop chargers over 60 watts ship with one. A lot of the loose cables in your junk drawer aren't.
So if your laptop charges slowly from a good brick, swap the cable before you blame the brick. Keep one properly rated cable with the charger and label it. Tape and a marker work fine. That cable goes back in the bag every time, not into the drawer, and not to your brother-in-law.
What to buy, what to skip
Buy:
- A brick whose published table covers the multi-port case and matches your gear.
- Two USB-C ports at minimum. Three if you travel with a laptop, phone and tablet or earbuds.
- A wattage total about 20 percent above what you'll realistically run at once. That headroom keeps it cooler, and cooler lasts longer.
- A certification mark on the actual unit.
- A fold-flat prong design if it's going in a bag. Prongs that don't fold will find the one soft pocket in your luggage and gouge it.
Skip:
- Any charger that advertises a total wattage and shows no per-port breakdown.
- Anything unusually light for its stated wattage with no name or support page. Heft isn't proof of quality, but a "100W" charger that weighs like a toy deserves suspicion.
- Bundles that pad the count with USB-A ports you won't use.
- Cheap unbranded cables, even if the brick is excellent.
I'm not naming a model because the lineups turn over every year and the label is the thing that never changes. Learn to read it once, and every charger you ever look at gets easier to judge.
Heat, and what to do about it
Fast charging generates heat, and heat is hard on batteries. A brick that's too small for what it's powering will run warm. A phone charging under a pillow or on a couch cushion runs warmer.
Put the charger where air can move around it. If you're charging a phone you plan to keep for years, an overnight trickle from a modest port beats a hot fast charge every night. That's one of the easier habits for making your next phone last five years, and it costs nothing.
Do this tonight
Gather every charger you own. Write down what each device needs, from the little label on the old charger. Then check the one brick you're considering, or already own, against that list.
It's the same habit as reading the home internet numbers that matter: the big figure on the front is marketing, and the one that decides your experience is further down the page.
Do that once and you'll own one brick and one cable that do the job. The airport outlet won't be a gamble, and neither will the hotel desk.
Dean Shaw
Gear & Garage
Reads the warranty, the parts list and the long-term owner reviews before anything else. Trucks, tools, watches, and the cheap version that costs more.
Watch
Worth an hour of your evening
More from Gadgets.
From channels we rate. Plays on YouTube.
Read next
