Skip to content
GuideEvergreen guide

Buy the hammer whose head can't come off

A loose head is the failure that hurts people. Here's how to buy a hammer that won't have one, and when the cheap one is fine.

By Wes Dunbar · Country & Skills6 min read
Buy the hammer whose head can't come off

Quick answer: If you want a hammer you never think about, buy a one-piece forged steel claw hammer. If you want wood, buy hickory with straight grain and a steel wedge across the eye. Skip anything with paint thick enough to hide the joint.

A hammer fails in one of two places. The head works loose, or the handle breaks. Everything else is marketing.

The loose head is the one that matters. A head that comes off mid-swing is a steel projectile with your arm behind it, and it usually goes past your ear on its way to somebody's window. So buy for the joint first, then for everything else.

Why heads loosen

A wooden handle is a bundle of fibers held in a steel eye. Wood moves with humidity. A hammer that lives in a hot truck bed all summer and a damp garage all winter shrinks and swells until the fit goes slack.

Then every strike works the head a little further. The first sign is a faint click on the follow-through. The second sign is the head sliding down the handle an eighth of an inch.

The old fix is to soak the head in a bucket of water overnight so the wood swells. It tightens things for a few days. It's a bandage, and the wood dries and shrinks again. Don't trust a hammer you've had to soak.

Why handles split

Almost every broken handle breaks at the neck, just below the head. Two causes account for most of them.

Misses. Swing a little low and the steel collar of the head isn't what meets the nail. The handle does. Do that a few times and the wood bruises, then cracks. If you see a dent on the neck of a hammer, that handle has already started to go.

Bad grain. Hickory is the standard for a reason. It's tough and it absorbs shock. But only if the grain runs straight down the length of the handle. When the grain wanders out the side of the neck, that's called runout, and it makes a handle that looks fine and snaps on a Saturday.

And yes, prying. Using a long claw hammer as a lever on a stubborn nail is a fair way to break one. Use a real bar for that. There's a whole argument about which bars are worth the money, and the answer is a short one.

Option one: forged steel, one piece

Head and handle are a single piece of steel. There's no joint, so there's nothing to loosen, and no wood, so there's nothing to split. Estwing is the name most people know for this design, and it's the one I'd tell a young guy to buy first.

The trade-offs are real:

  • It transmits more shock to your hand and elbow than hickory does. A grip sleeve helps, and it'll wear out eventually.
  • It's the wrong hammer for a day of framing if your elbow already complains.
  • You can't re-handle it. If the grip gets chewed, you replace the grip or the hammer.
  • The face is hard steel. Never strike it against another hardened tool, such as a cold chisel or another hammer. Hard steel on hard steel can chip, and chips fly. Use a brass or soft-faced tool when you're driving a chisel, or a proper mallet.

For a homeowner who builds a deck, hangs a gate, and fixes a fence, this is the right answer and it isn't close.

Option two: hickory, done right

A wood handle earns its place by being good to swing. It softens the shock. It feels alive in the hand. And when it finally does fail, you fit a new one.

That repairability is the real argument, and it's the same one I'd make about buy-it-for-life tools in general. A good head on a replaceable handle outlasts a hammer that must be thrown away when one part dies.

What to look for in the store:

  • Sight down the handle. Look for grain lines running straight along its length, not drifting out the side.
  • Look at the top of the eye. You want a wooden wedge driven in lengthwise, plus a steel wedge set across it. A single small wood wedge is the minimum. The steel one is what keeps the head on when the wood shrinks.
  • Check for a gap between the wood and the steel at the collar. Run a fingernail around it. There shouldn't be a ridge.
  • Be suspicious of thick finish. A heavy glossy coat of lacquer or paint can hide everything above. A good handle has a thin finish you can see through.
  • Give the head a twist by hand. If it moves at all on a new hammer, put it back.

Option three: fiberglass or steel-core composite

A fiberglass handle won't split and doesn't care about humidity. Some have a steel core running up into the head. They shrug off weather and they're good on a job site where tools sit in the rain.

The catch is repair. When the head does come loose or the handle is damaged, you usually can't fix it. They're also less pleasant than hickory to swing, and a miss that would only dent a wood handle can chew into the glass. Fine for a truck toolbox. I'd still pick steel or hickory for the bench.

What size

For general work, a 16-ounce claw hammer is the one. It drives a sixteen-penny nail without wearing out your wrist and still lets you tap a small finish nail without wrecking the board. A framing hammer runs heavier, commonly 20 to 22 ounces, and is built for long days of big nails. If you aren't framing a house, you don't need it.

Pick a curved claw for general pulling and driving. Straight claws are for ripping things apart.

When the cheap one is right

I'd say the cheap one is right more often than people admit, as long as you know what it's for.

Buy a bargain hammer for the demolition bucket. If you're tearing out a fence and driving a hammer into things that will wreck it, spend as little as you like and use it up. Buy one to lend, too. A cheap hammer is the one that goes home with the neighbor, and you won't lie awake over whether it comes back.

A cheap one also suits the person who hangs a picture twice a year. For that use, a plain hammer will do fine for a decade.

What it costs you is the joint. Cheap wooden hammers tend to be the ones with the single small wedge, the thick paint, and the wandering grain. Spend ten minutes at the rack with the checks above and you'll find the decent ones.

If the head's already loose

Don't use it. Rehang it:

  1. Put on safety glasses.
  2. Saw the old handle off flush at the head and drive the stub out of the eye. Clamp the head in a vise with padded jaws if you can.
  3. Fit the new handle. It should seat snugly. Shave it with a rasp if it doesn't.
  4. Saw the kerf, drive in the wooden wedge with glue, and trim it flush.
  5. Drive a steel wedge across it.

Then do what any decent man does. When you borrow a hammer, bring it back with the handle wiped down and the face clean. When you lend one, make it the cheap one.

Wes Dunbar

Country & Skills

Grew up on an acreage and never quite left. Covers trucks, trades, land, and how to do the thing yourself.

Watch

Worth an hour of your evening

More from Gear.

From channels we rate. Plays on YouTube.

    Marques BrownleeNov 17

    Can You Trust MKBHD?

    Marques BrownleeNov 11

    Macbook PROLED Review: It's Not About That

    Marques BrownleeNov 6

    Meta VR Glasses: What Vision Pro 2 COULD Have Been!

    Outdoor EmpireSep 12

    Amazon vs Walmart Camping Gear: What's Actually Worth Buying?