Tune your table saw so it cuts square and stops binding
A saw that burns, pinches or kicks back is usually out of alignment by a few thousandths of an inch. Here's how to find it and fix it in order.

Quick answer: Unplug the saw, square the blade to the table, line the blade up with the miter slot, then set the fence parallel to the slot or a hair open at the back. Confirm the riving knife sits in line with the blade. Each step takes minutes, and a bad one is what makes a saw bind.
Binding is when the board pinches the back of the blade, the motor bogs, the wood scorches, and sometimes the board gets thrown back at your midsection. The wood is rarely the first thing to blame. Most of the time the blade and the fence aren't pointing the same direction, and the board gets squeezed between them.
Before you touch anything
Pull the plug out of the wall. Switching it off isn't enough, and a saw with the power button in reach is how people lose fingertips during a "quick adjustment." If the cord is frayed or the plug is damaged, stop there. That's an electrical repair, and this piece on which wiring jobs are worth doing yourself will tell you where the line is.
Then remove the throat plate and the blade guard if it's in the way. Raise the blade all the way up. Put on safety glasses, because you'll be running test cuts later.
You need a few things, and none of them cost much:
- A decent machinist's or combination square (one you've checked against a known edge)
- A tape measure or dial caliper
- A permanent marker
- The wrenches that came with the saw, or the right sizes
- Two or three pieces of scrap, ¾-inch thick and a few inches wide
Check the blade first
Spin it by hand. Look for pitch and resin caked on the teeth and plate. Gummed-up carbide cuts hot, and a hot blade burns wood and binds all by itself. Wipe it down with a blade cleaner and a brass brush.
Look at the plate for a bend or a wobble. A blade that's visibly out of true goes in the trash. A good blade costs less than an emergency room visit.
Make sure the arbor nut is snug and the flanges are clean. A speck of sawdust trapped behind a flange will tilt the blade a hair. That's the kind of error you'll chase for an hour if you skip this check.
Square the blade to the table
Crank the blade to 90 degrees. Stand your square on the table and bring it against the flat of the blade plate, in the gap between teeth. Never against a tooth. Carbide tips are set wider than the plate, so a square resting on a tooth will lie to you. Rotate the blade until there's a clear spot.
Look for light between the square and the plate. Any wedge of light means you're off.
Find the 90-degree stop on your saw, usually a bolt or screw under the table or at the tilt mechanism. Your manual shows where. Loosen the lock, turn the stop bolt, bring the blade to the stop, and check again. Repeat until there's no light.
Ignore the angle pointer on the front of the saw until you're done. They're rarely accurate out of the box. Reset the pointer to zero last.
Line the blade up with the miter slot
This is the adjustment people skip, and it causes most of the binding.
Pick one tooth that's bent toward the slot side. Mark it with the marker. Raise the blade to full height. Measure from the edge of the slot to that tooth at the front of the blade, with the tooth at table height. Write the number down.
Now rotate the blade by hand until the same tooth is at the back, still at table height, and measure again. Always use the same tooth. The set varies from tooth to tooth, and using two different ones will fool you.
The two numbers should match. A sheet of copy paper is roughly four thousandths of an inch thick. If you're off by a couple of sheets, fix it.
How you fix it depends on the saw:
- Contractor and hybrid saws: Loosen the trunnion bolts under the table and nudge the trunnion until the readings match.
- Cabinet saws: The trunnions usually stay put. You loosen the bolts that hold the tabletop and shift the top.
- Jobsite saws: Some have adjustment screws, and some are fixed. Check the manual before you start loosening things.
Snug the bolts, measure again, then tighten fully and measure a third time. Tightening almost always moves things. Check the 90-degree stop again too, since moving the trunnion can nudge it.
Set the fence
A fence that tilts in toward the blade at the rear is the single most common reason a board pinches. Clamp the fence a few inches from the blade, measure from the slot to the fence at the front, then at the back.
The best setup is dead parallel. The second-best, and the one a lot of experienced woodworkers prefer, is a hair open at the back, a few thousandths wider than the front. That gives the board room to move off the blade once it's cut. A fence closed at the back is a trap.
Adjust it with the screws or bolts at the head of the fence. After that, lock it down and check once more.
Align the riving knife
The riving knife is the thin steel blade that rides behind the saw blade. It keeps the two halves of a cut from closing up on the back of the blade. It has to sit exactly in line with the plate.
Lay a straightedge against the blade plate and run it back toward the knife. The straightedge should touch the knife along its whole length. Most knives are just thicker than the plate and just thinner than the kerf. If the knife is kinked or bent from a drop, replace it.
The gap between the blade and the knife should be about an eighth of an inch. The knife should sit slightly below the top of the blade, never above it, so it doesn't block a non-through cut. Your manual gives the exact clearance for your saw.
Run the test cut
Put the throat plate back in. Set the blade so the gullets, the valleys between the teeth, just clear the top of the wood. That's usually about a quarter inch above the board. Higher than that exposes more blade than you need.
Cut two pieces of scrap. Take one cut edge from each and set them face to face, with one flipped over. If there's a gap at the top or bottom, the angle is off, and the gap you see is double the real error. Go back to the 90-degree stop.
Check the cut face with the square. It should land flat with no light. The kerf should look clean, with no burn marks on the cut edge. Scorching means the fence is closing in, the blade is dull, or the alignment is still off.
Habits that keep the saw from biting
A square saw still kicks if you feed it wrong. Stand slightly to one side of the blade, never directly behind the board. Use a push stick on narrow cuts and keep your hands out of the blade's line. Don't use the fence and miter gauge together for a crosscut, because the trapped offcut will get launched. And never rip a warped board with the bowed edge against the fence. Joint it flat first or cut it another way.
If you do get cut, press down on the wound hard and get medical help right away. Read what to do in the ten minutes before the ambulance arrives before you ever need it.
Recheck this alignment twice a year, and after anyone moves the saw. A quarter hour with a square beats a lifetime of working around a saw you don't trust.
Wes Dunbar
Country & Skills
Grew up on an acreage and never quite left. Covers trucks, trades, land, and how to do the thing yourself.
Watch
Watch how it's done
Picked for this article.
From channels we rate. Plays on YouTube.
Grizzly Industrial, Inc.
How To Align a Table Saw Blade to Miter Slot and Fence
Rockler Woodworking and Hardware
How to Align Your Table Saw Fence | Rockler Skill Builders
Read next
